TROBA-LEVEL configurator

• Please choose the suitable floor plan of your terrace.

  
  
  

  Please enter the dimensions for the selected floor plan.

• Please enter the dimensions of the pavers you want to install.

  Paver width (in cm)

  Length of paver (in cm)

  Paver thickness (in cm)

• Please enter the desired height of the finished floor as the distance between the upper edge of the substrate to the upper edge of the covering at the corner points of the floor plan (see drawing). Note the position of the house wall.

  Height at point A (in cm)

  Height at point B (in cm)

  Height at point C (in cm)

  Height at point D (in cm)

  

• Please specify whether to include a drain within the balcony or terrace area in the calculation. If yes, please enter the position and height of the drain. The position is the distance of the drain's centre to the edge of the balcony or terrace. The height is the distance of the upper drain edge to the upper edge of the covering.

  Due to the complexity of the drain calculation, the forms "T", "L" and "U" cannot be considered at the moment.

  Include drain

  Outlet

  
  

• Please select the desired installation type and the angle. Then specify the starting point, from which the installation is to begin.

  Type of installation Cross joint Half-offset assembly

  Installation direction Horizontal, 0°

  Starting point

  Caution! A paver support is located on the outlet. Please keep in mind for further planning.

  Automatic starting point selection

  Distance to side a (in cm)

  Distance to side b (in cm)

• Legend

  	Paver supports
  	Paver support, spacing too small
  	Outlet
  	Full paver
  	Cut paver

  Please check your entries and correct them in the respective tabs if necessary.

  Area	m²
  Paver dimensions (W x L x H)	cm x cm x cm
  Number of full pavers
  Number of cut pavers
  Number of support points

  ---

  Options

  	Install without rotatable component TROBA-LEVEL-PLV 60 Only stackable products are suitable. This solution generally results in higher material costs, and may result in a quicker installation.
  	Use flexible connectors The covering may shift horizontally due to external factors and may tilt in places. Adaptive connectors can prevent tilting. To this end, every paver support point must be capped with TROBA-LEVEL-PL 10.
  	Use load distribution disks for stacked support compenents TROBA-LEVEL-LV 3, Exclusively stacked supports have a smaller base area. Depending on the load, it may be helpful to use additional load distribution disks with a larger base area to protect the substrate.
  	Use spot protection for the substrate (if no full area protection is in place) (TROBA-LEVEL-PLS 6) Special protection for the substrate or the waterproofing assembly can be implemented in spots or over the full area.

  Result

  Based on the estimated calculation of the most economical product combinations, you will require the following products for your project. If desired, you may replace the calculated unit numbers with values of your own.

  Photo	Product information	Number of units (calculated)	Ordering quantity	Ordering unit	Individual price	Total price
  	TROBA-LEVEL-AP 1 Item no.: TLAP1 Levelling plate Packaging unit: 8 Packages Packages = 250 units	units		Packages	£	£
  	TROBA-LEVEL-PL 10 Item no.: TLPL10 Stackable paver support Packaging unit: 100 units	units		Units	£	£
  	TROBA-LEVEL-PLA 30 Item no.: TLPLA30 Height adapter Packaging unit: 52 units	units		Units	£	£
  	TROBA-LEVEL-PLV 60 Item no.: TLPLV60 Height-adjustable paver support Packaging unit: 48 units	units		Units	£	£
  	TROBA-LEVEL-LV 3 Item no.: TLLV3 Load distribution disk Packaging unit: 100 units	units		Units	£	£
  	TROBA-LEVEL-PLS 6 Item no.: TLPLS6 Protective pad Packaging unit: 1 Packages Packages = 10 units	units		Packages	£	£
  	TROBA-LEVEL-PLA 70 Item no.: TLPLA70 Height adapter Packaging unit: 30 units	units		Units	£	£
  					Total price:	£

  This data generated by the configuration tool is intended for guidance only. This information is issued without warranty. Users are responsible for verifying all generated results and matching them to actual requirements.

  Print out results

Back Continue